Error Code P0663 is defined as Intake Manifold Tuning Valve Control Circuit/Open Bank 2. This is a generic trouble code, meaning it applies to all cars equipped with the OBD-II system, particularly those made since 1996 up to present. This includes models from, but not limited to Acura, Chevrolet, Chrysler, Dodge, Ford, Honda, Isuzu, Land Rover, Porsche, Saturn, Vauxhall, etc. Specifications on the definition, troubleshooting, and repairs, of course, vary from make, model, and powertrain configuration.
The PCM (powertrain control module, also known as ECM or engine control module in other 2017 Volvo S90 makes) is responsible for monitoring and adjusting multiple sensors and systems involved in the operation of your 2017 Volvo S90 . Including detects faults within said systems and circuits. One of these systems that the PCM is responsible is monitoring and correlating with desired values is the Intake Manifold Tuning Valve.
Commonly called the “flapper” valve, this piece comes up often in the repair world. The intake manifold tuning valve comes with many possible purposes to help the engine in both performance and drivability. It regulates the pressure between intake plenums, or redirect intake air to separate set of intake runners (or combination) to change the flow and possibly the performance of the engine. This valve is usually made of plastic, and with notoriously high temperature inside the engine compartment, it’s common to see problems with this component.
Error Code P0663 is as Intake Manifold Tuning Valve Control Circuit/Open Bank 2, meaning the PCM has detected a general electrical fault or open electrical situation. Bank #2 refers to the side of the engine that does NOT contain the cylinder number 1.
This code is usually triggered by either a mechanical or electrical fault with the intake manifold tuning valve. If you’re driving a 2017 Volvo S90 in an area with susceptible extreme cold weather, this can cause the valve to malfunction and not rotate properly according to PCM’s desires.
As with most codes, the first step in diagnosing this code is to check with the TSB (Technical Service Bulletins) and look for known issues with the specific 2017 Volvo S90 .
Advanced diagnostic steps are usually 2017 Volvo S90 specific, and require special advanced equipment and knowledge to diagnose the problem accurately. Below is the basic diagnostic step, but make sure you refer to your 2017 Volvo S90 year, make, model, and powertrain configuration for the specific steps of your 2017 Volvo S90 .
Start with clearing the codes to see if the error code comes back immediately. If it does NOT come back, take your 2017 Volvo S90 for a long and test drives to see if it comes active again after a few drive cycles. If it does come back, then proceed with the diagnosis.
Then, locate the intake manifold tuning valve. This can be tricky, as, in many models, they’re internally mounted in the intake manifold itself. With that said, the connector for the valve must be fairly accessible. Thus, check it and look for signs of damage such as broken tabs, melted plastics, etc. Also, make sure there is enough electrical connection.
Depending on the capabilities of your scan tool or OBD code reader, you may be able to use it to operate the valve electronically. If this option is available for you, then you have a good way to check whether the valve is operating through its full range or not. Also, if you hear any clicking noises from the intake, then make sure to check the intake manifold tuning valve. If there is an abnormal clicking noise coming from the intake while you’re adjusting the sensor using the scanner, then you have an obstruction on your valve, or the valve itself may be stuck.
From here, you can proceed on removing the valve and check it thoroughly to look for signs of obstructions in the manifold. If you find no obstructions and clicking is still present, then you can try replacing the valve.
Note that in some cases, this can be a difficult task, so make sure you research your 2017 Volvo S90 beforehand and know the right parts and tool you can use.
Also, refer to the manufacturer’s technical data when performing diagnosis and repairs.
Inspect the harness involved in the tuning valve. The wiring harnesses must be routed through the engine parts and other high heat areas. Not to mention engine vibrations can cause chafing and cracking.
If you have done everything and the symptoms and problems persist, then check the PCM, especially if there are multiple related codes present, or the problem is coming on and off intermittently.
The most common fix of this code is the repair or replacement of bad wiring, connectors, and modules. Other common repairs include:
Using the downloaded freeze frame data to address the codes in the order they occurred can help mechanics avoid the common mistakes in repairing the symptoms of Error Code P0663, along with other stored codes.
To avoid serious problems associated with this code, such as stalling, rough riding, and increased fuel consumption, this code must be addressed as soon as possible.